Clean your magazines after each use
If you want to keep your airsoft magazines working properly, it is important that you clean them after each use. This will extend the lifetime of your magazines and prevent any malfunctions or jams from occurring.
One of the best ways to clean your magazines is by using a high-quality lube on them. You can use a specialized lubricant that is made specifically for airsoft guns, or an all-purpose gun oil like WD-40. Simply apply some lube directly onto the magazine and run it through several times with a duster or cloth until the excess has been removed.
In addition to cleaning your magazine after each use, be sure to check regularly for signs of wear or corrosion. A quick visual inspection can help you spot any damage to the magazine and take action before it causes a jam or other malfunction.
If you follow these tips, your airsoft magazines should last for years without any issues. So be sure to clean them regularly and keep them well-maintained for optimum performance!
Remove the spring and follower
The first step in cleaning your airsoft magazine is to remove the spring and follower. This can usually be done by sliding them out of one end of the magazine. Once they are removed, you will be able to access all of the internal parts for thorough cleaning.
After removing the spring and follower from your magazines, you should use a small brush or cloth to clean any dirt or debris from inside the magazine. This will help prevent jams and other malfunctions as well as prolonging the life of your magazines overall.
Be sure to also inspect all of the internal components for signs of damage or wear, such as cracks in the feed lips or deformation around the firing pin. If you notice any issues, you may need to replace these parts in order to keep your magazines working properly.
Once you have cleaned and inspected your magazine, you can reassemble it by putting the spring and follower back into place. Then, give the entire magazine a final wipe down with a clean cloth or duster to remove any remaining lube or debris, and it should be ready for use again. With regular cleaning and maintenance, your airsoft magazines should last for many years without any issues!
Soak the magazine in a solvent bath
If your airsoft magazine is really dirty, you may want to soak it in a solvent bath to remove all of the dirt and grime. This is especially effective if the magazine has been sitting for a while and is starting to show signs of corrosion.
To do this, simply fill a container with a cleaning solvent like dish soap or rubbing alcohol. Submerge the magazine in the solvent and let it soak for a few hours. This will loosen up all of the dirt and grime so that it can be easily wiped away.
After soaking the magazine, use a brush or rag to scrub away any remaining dirt. Be sure to pay special attention to the feed lips and any other areas where dirt or grime might build up.
Dry the magazine off and reassemble
Once you have finished cleaning your airsoft magazine, it is important to dry it off completely before reassembling. This will help prevent any corrosion or rust from forming on the metal parts.
The best way to dry your magazine is by using compressed air. Simply point the nozzle of the air compressor at the magazine and blast away any remaining water or solvent. You can also use a hairdryer on the low setting, but be careful not to overheat the plastic parts of the magazine.
Once the magazine is dry, you can reassemble it by putting the spring and follower back into place. Then, give the entire magazine a final wipe down with a clean cloth or duster to remove any remaining lube or debris, and it should be ready for use again. With regular cleaning and maintenance, your airsoft magazines should last for many years without any issues!
Lube your magazines every few games for optimal performance
It is also a good idea to lube your airsoft magazines every few games. This will help keep the moving parts working smoothly and prevent any jams or other malfunctions.
To do this, simply apply a light layer of silicone oil or another lubricant to all of the moving parts of the magazine. Be sure to avoid getting any lube on the outside of the magazine, as this can attract dirt and grime.
After applying the lubricant, work the follower up and down a few times to spread it around evenly. Then, wipe away any excess lube with a clean rag or cloth. Your magazines should now be ready for use again!
Conclusion
By following these tips, you can keep your airsoft magazines in good condition for many years. Remember to clean them regularly, lube the moving parts, and inspect them for any signs of wear or damage. With proper care, your magazines will provide you with years of trouble-free use!